Choosing Bonsai Driftwood for a Betta Tank
Quick answer: For most betta tanks (5 to 20 gallons), pick one small bonsai driftwood tree, reaching about half the water height, with smooth branches and an open canopy. Place it slightly off-center, leave open swimming space at the front, and add a thin layer of moss to the top so your betta has a shaded spot to rest near the surface. Our Small box is the usual fit: about 5+ random trees, so you can choose the best one for the tank and keep the rest for later.
A bonsai tree gives a betta tank a focal point that looks like a tiny landscape instead of a plastic ornament. Bettas are slow swimmers with long fins and like to rest high in the water, so the right tree is less about size and more about shape, texture and placement. This guide walks through each choice.
What makes a tree work well in a betta tank
Height. Bettas breathe air at the surface and spend a lot of time in the top third of the tank. A tree that reaches about half to two thirds of the water height gives them a canopy to rest under without blocking the surface. In a 5 gallon tank that is usually a tree around 5 to 7 inches tall; in a 10 gallon, 7 to 9 inches.
An open canopy. Look for branches that spread out with gaps between them rather than a tight cluster. Open branches let your betta swim through without catching fins, and they hold moss better because light reaches every pad.
A stable base. A flat or wide base keeps the tree upright when you clean the tank or when the betta pushes against it. If the base is narrow, bury it a little in the substrate or set it on a flat stone.
Smooth texture. Long betta fins can snag on sharp points or splinters. Before the tree goes in, run a piece of nylon stocking or a soft cloth over every branch. If it catches, sand that spot lightly with fine sandpaper and rinse the dust off.
Which box fits a betta tank?
Each box is a random assortment of trees, so shapes and exact sizes vary. Current options from our shop:
- Small box — about 5+ trees, $69. A good fit for betta tanks and small aquascapes. You get several trees to try in different spots and can keep spares for a second tank.
- Mini box — about 3+ smaller trees, $19.99. Good for a 3 to 5 gallon betta tank or a desk tank where a full-size tree would crowd the space.
- Medium box — about 8+ trees, $79. Worth it if you keep several betta tanks or want spares for later rescapes.
Not sure which size fits your tank? The size guide compares tree counts and typical tank sizes side by side.
Step 1: Prepare the tree
Every tree should be rinsed and soaked before it goes in your tank. Soaking helps the wood sink and lets you see whether it releases tannins, the natural tea color that some driftwood gives off. Our driftwood preparation guide covers rinsing, soaking and weighing the tree down step by step.
Step 2: Plan the layout
Bettas do well with a simple layout. A few ideas that work in rectangular tanks:
- Rule of thirds. Put the tree about one third in from the left or right side. It looks more natural than dead center.
- Open front. Keep the front half of the tank mostly open so you can see the fish and it has room to flare and swim.
- Low plants around the base. Cryptocorynes, a few anubias on a stone or a carpet plant make the trunk look grounded.
- Floating plants nearby. Frogbit or salvinia near the tree gives extra shade at the surface, which many bettas use.
Leave a gap between the top of the canopy and the water surface so your betta can always reach air.
Step 3: Add moss for a resting canopy
Our trees ship bare, and the moss is yours to add. A thin layer of java moss, christmas moss or flame moss on the top branch pads turns the tree into a green canopy. It also gives your betta a soft, shaded place to rest. Keep the layer thin so light reaches the inside, and trim it every few weeks to hold a rounded bonsai shape. Our guide on how to attach moss to bonsai driftwood shows the thread and glue methods.
Step 4: Watch the first week
After the tree goes in, watch how your betta uses it. Most will explore the branches and pick a favorite resting spot within a few days. Check the fins for small tears during the first week. If you see any, find the branch that caused it and smooth it down.
If the water turns a light tea color, that comes from tannins in the wood. Regular water changes clear it over time, and activated carbon in the filter speeds that up. Our guide on preparing driftwood explains how a longer soak reduces it before the tree goes in.
Common mistakes
- A tree that is too tall. If the canopy touches the surface, it takes away air space. Pick a shorter tree or set it lower in the substrate.
- Too many trees in a small tank. One tree usually looks better in 5 to 10 gallons. Save the rest of the box for another tank or a later rescape.
- Thick moss on day one. A heavy clump blocks light and the inner layer turns brown. Start thin and let it fill in.
- Skipping the fin check. A two-minute run with a stocking over the branches saves torn fins later.
FAQ
What size bonsai driftwood is best for a 5 gallon betta tank?
A tree around 5 to 7 inches tall usually fits. The Mini box and Small box are the best starting points for tanks this size; each box is a random assortment, so exact sizes vary.
Can a betta tank have more than one bonsai tree?
Yes, in 10 gallons and up two trees at different heights can look like a small forest. Keep open swimming space in front and make sure the canopy does not cover the whole surface.
Will the driftwood float?
Many pieces float at first. Soaking until the wood is waterlogged, or weighing it down with a stone for a while, helps it sink. See the preparation guide for details.
Do the trees come with moss?
No. Trees ship bare and you add your own moss. Every box is a random assortment of shapes and sizes.
How does shipping work?
Boxes ship on Wednesdays to the Lower 48 states, with tracking after packing. All sales are final.